Satellite setup for NTV Plus in 2026

A question that often arises for satellite TV users is which satellite to choose for NTV Plus to work correctly. In 2026, it is important to properly set up the satellite to get a quality image and a stable signal. In this guide, I will share step-by-step instructions for setting up CCcam and OScam, as well as discuss the choice of satellite for NTV Plus.

Choosing a satellite for NTV Plus

Before starting the setup, you need to decide on the choice of satellite. This is an important step, as it affects the signal quality and channel availability.

Types of satellites

Various types of satellites can be used to receive NTV Plus. The most common are Astra and Eutelsat. These satellites provide good coverage and a stable signal. I have checked both options, and in my experience, Astra shows better results in most regions of Russia.

Selection parameters

When choosing a satellite, it is important to consider several factors:

• Coverage: Make sure the chosen satellite covers your region.
• Signal quality: Check which frequencies and polarizations the satellite supports.
• Compatibility with equipment: Ensure that your equipment supports the chosen satellite.

Setting up CCcam for NTV Plus

Setting up CCcam may seem complicated, but in fact, it is a process that can be completed in a few steps.

Installing CCcam

To install CCcam, run the following commands in your device's terminal:

After installation, you will need to find the configuration file. It is usually located at/etc/CCcam.cfg.

CCcam.cfg configuration

Now open the configuration file:

In this file, you need to specify your server parameters. An example configuration might look like this:

After making changes, save the file and restart CCcam:

Setting up OScam for NTV Plus

Setting up OScam is similar to setting up CCcam, but with some differences in configuration.

Installing OScam

To install OScam, run the following commands:

The OScam configuration file is usually located at/etc/oscam/oscam.conf.

OScam.conf configuration

Open the OScam configuration file:

An example configuration might look like this:

[global]
logfile = /var/log/oscam.log
maxlogsize = 1000
nice = -1

[webif]
httpport = 8888
httpsport = 443

Don't forget to configure the file/etc/oscam/oscam.server для подключения к вашему серверу:

[reader]
label = mycard
enable = 1
protocol = internal
device = /dev/sci0

После настройки перезапустите OScam:

sudo systemctl restart oscam

Troubleshooting during setup

Even experienced users sometimes encounter problems. Here are some common scenarios.

Common errors

One of the most frequent mistakes is incorrect antenna setup. Make sure your antenna is pointed towards the satellite and has the correct tilt angle. It's also worth checking the connection parameters.

Diagnostic methods

If there is no signal, try the following steps:

• Check the cable connections.
• Restart the receiver.
• Use diagnostic tools to check the signal level.

Additional settings for NTV Plus

Sometimes, to achieve optimal image quality, additional adjustments may be needed in your system. This may include changing antenna parameters or configuring additional equipment.

Antenna setup

Antenna installation parameters can significantly affect signal quality. Make sure the antenna is properly installed and securely fastened. I recommend using the signal level to adjust the tilt angle and rotation of the antenna. Most modern receivers have built-in signal level indicators.

If you have the option, try using a motorized antenna. This will allow you to switch between multiple satellites, expanding your access to channels. Motors like DiSEqC make it easy to switch satellites using a remote control.

Using a multi-feed

If you plan to connect multiple receivers or TVs, consider using a multi-feed. This device allows you to connect multiple lines to one satellite. Make sure your multi-feed supports the required number of connections and meets your needs.

Legal aspects of using CCcam and OScam

It's important to remember the legal aspects of using CCcam and OScam. In some countries, the use of such services may be restricted or even prohibited. I recommend always checking the current laws in your region to avoid legal issues.

In Russia, the use of satellite television with CCcam and OScam is not prohibited, but you need to be careful when choosing providers and servers. Make sure you are using legal content sources. Using pirate servers can lead to legal consequences.

Tips for choosing a provider for CCcam and OScam

When choosing a provider for CCcam or OScam, several factors should be considered:

• Reputation: Look for providers with good reviews and a long track record in the market.
• Quality of service: Make sure the provider offers customer support and responds quickly to issues.
• Connection speed: Check how fast the server operates to avoid delays while watching.
• Price: Compare the costs of different providers, but don't choose solely based on price. Quality matters.

I recommend doing some research, reading reviews, and communicating with other users before making a decision.

Software updates

Don't forget to regularly update the software of your receiver and CCcam and OScam servers. Updates may include bug fixes, performance improvements, and new features. Usually, the update process is quite simple and can be done through your device's interface.

For OScam, updates can be performed via the command line using the commands:

Don't forget to restart OScam after updates for the changes to take effect.